Calculated-industries 6130 v3.0 User Manual

SCALE MASTER®IIv3.0ADVANCED DIGITAL PLAN MEASUREModel 6130

“Rolling” a MeasurementTo take a measurement with the ScaleMaster II:1) Switch the unit on. If the displaydoes not show zero (0), press the[Reset] key

User’s Guide – 11

Built-In ScalesImperial (English) UnitsArchitect Engineer-I Engineer-II MapARCH ENGI ENGII MAP1 foot= 1 inch= 1 inch= 1 inch=1/32” 10.0’ 300.0’ 1.0 Mi

Metric UnitsArchitect Engineer-I Engineer-II MapARCH ENGI ENGII MAP1:1 1:100.0 1:1,000 1:100k1:2 1:125.0 1:1,250 1:125k1:3 1:150.0 1:1,500 1:200k1:4 1

You can also convert values fromImperial Units (English) to MetricUnits within the Imperial mode.B) Press [Set] [Mode] and continuepressing [Mode] to

Locking Scale SettingsYour Scale Master II comes equipped witha lock switch that prevents inadvertentlychanging drawing scales. When the lockis activa

3) You can continue to add values us-ing the [M+] key. Press [Rcl] [M+] toreview the total in Memory.*Note: For count values, you must pressthe [Count

Other Memory Function Keystrokes[Set] [M+]Replaces the contents of Memorywith the displayed value.[Set] then [Sub] and [M+] simultaneouslyReplaces the

Programming ModeThe Scale Master II allows you to pre-set values into frequently used keys,including: ◆ Custom Scales (4 Imp/4 Met)◆ Auto-Count distan

Setting Custom ScalesYou can program and store eight Cus-tom Scales: four in Imperial (English)and four in Metric Units. The defaultunits of measureme

Preliminary InformationIntroduction . . . . . . . . . . . . . . . . . . . .3Key Definitions . . . . . . . . . . . . . . . . .4Adjusting the Wheel .

4) Press [Scale]. The appropriate an-nunciator will begin flashing “FT-IN“ for Imperial Mode, “MM” forMetric Mode.5) If you want to change the units o

Setting a Custom Scale1) Press [Mode] until 1:CUS_x (x beinga number 1-4) appears in the scalebox display. 2) Press [Set] [Scale]. “ROLL” will ap-pear

the next digit. You can press the[Mode] key to move back one digit.6) Once the desired value has beenset, press [Set] to store the valueand exit the p

Setting an Auto-Count ValueThe Scale Master II has an Auto-Countmode that allows you to count howmany times you’ve rolled a certain dis-tance. You wil

4) Press [Set] to save changes and putthe unit into auto-count measuringmode.5) Roll a distance. The unit will beepeach time you roll the programmeddi

Setting a Constant Value (+K)This key is used to add a pre-pro-grammed value to the displayed mea-sured value. If the value is not “live,” then pressi

3) Press [M+] to increment the dis-tance. When you have reached thecorrect number, press [Scale] to ad-vance to the next digit. Press[Mode] to move b

Finding Area and VolumeThe Scale Master II can calculate areaand volume once you have your valuesset for length, width, and (for volumecalculation onl

2) Roll the second dimension andpress [Width]. This value is storedas the width and the main displaywill reset to zero.3) Press [Sq/Cu] to calculate t

b. To Enter and Store a Height:i. If you are entering a height(instead of rolling), press [Set][SQ/CU].ii. If you do not want to changethe unit of mea

IntroductionThe Scale MasterII Multi-Scale DigitalPlan Measure has been specificallydesigned to simplify take-offs fromarchitectural and engineering d

Other Area/Volume Function Keystrokes[Rcl] [Length]Displays the value stored in theLength register.[Rcl] [Width] Displays the value stored in theWidth

Connecting to a PC (optional)The Scale Master II has a built-in com-puter interface connection so that youcan use it with estimating and spread-sheet

Basic Functions PCYou can send a value using the [Set]key, then store it as Length, Width,Height, or in the memory, as you nor-mally would. Remember,

Auto-Count Function PC[Rcl] [Set] [Count]Enters Auto-Count programmingmode. The next press of [Set] exitsAuto-Count mode.[Reset] and [Count] simultane

Error/Auto-Range FunctionError Message – If you make an incor-rect entry (such as trying to add di-mensioned and non-dimensionedvalues), the Scale Ma

Battery/Automatic Shut-OffThe Scale Master II is powered by two3-Volt CR-2430 Lithium batteries (6volts total). To conserve battery power,the unit wil

Register Values/SettingsPermanent Values/SettingsThe following registers/settings will remain in permanent storage, onlychanging:1) when the settings

Semi-Permanent Values/SettingsThe following registers/settings arecleared when the Scale Master II is powered down:Register Default DefaultSetting Imp

SpecificationsPower Source:Two 3-Volt CR-2430 lithium batteries.Approximately 400 hours normal use.Display Method:LCD with zero suppression, commas an

Repair and ReturnWarranty, Repair and Return InformationReturn Guidelines:1.Please read the Warranty in thisUser's Guide to determine if yourCalc

Key Definitions[Off/On] – Power On/Off switchTurn power On or Off. Turningpower Off clears the display and allvalues previously stored in Mem-ory. Tur

Limited WarrantyCalculated Industries, Inc. (“CII”) warrants thisproduct against defects in materials and workman-ship for a period of one (1) year fr

Repair Service — Outside the USANot all countries have CII Authorized ServiceProviders or the same warranty and service policies.To obtain warranty or

FCC Class BThis equipment has been certified to comply withthe limits for a Class B computing device, pursuant toSubpart J of Part 15 of FCC rules.Leg

How To Reach Calculated IndustriesUser’s Guide – 43MailCalculated Industries, Inc.4840 Hytech DriveCarson City, NV 89706 U.S.A.Phone1 (775) 885–4900Fa

Designed in the United States of America Printed in ChinaUG6130E-E7/05

[Sub] is pressed simultaneously with[Count], [+K] or [M+], the unit willsubtract the appropriate value.[Count] – Count keyUsed to increase the Count v

When in programming mode, thiskey moves the cursor back to theprevious item programmed.[Scale] – Scale key Used to cycle through the variousscales wit

[Sq/Cu] – Area/Volume key Used to set or view height andcalculate area and volume: 1) The first press of this key calcu-lates and displays the area us

Adjusting the WheelThe Celcon®polymer wheel can be ad-justed for each user’s preference. Toadjust the wheel, take a small, flat-headjeweler’s screwdri

Imperial/Metric ModesThe Scale Master II is set up to useImperial (English) dimensionalunits by default. The Scale Master IIcan be set up to use Metri