Function Keys[M+] – Memory Plus Adds the displayed value to the accumulative value.[RCL] [M+] – Memory Recall Displays the value stored in accumulat
Rotate to Adjust WheelAdjusting the WheelThe Celcon® polymer wheel can be adjusted for each user’s preference. To adjust the wheel, take a small, flat
PreferencesPreferences allow customization of how the Scale Master Pro functions during certain operations. The following preferences are available:Bu
Setting Preferences:1) Press [SET] [MODE] to access the preferences.2) Press the [COUNT] (S) key to move up or the [RCL] (T) key to move down through
Imperial/Metric ModesThe Scale Master Pro is set up to use Imperial (Standard) dimensional units by default. The Scale Master Pro can be set to Metric
Metric UnitsArchitect Engineer-I Engineer-IIARCH ENGI ENGII1:50 1:100.0 1:1,0001:75 1:125.0 1:1,2501:1 1:150.0 1:1,5001:2 1:200.0 1:1,6251:3 1:250.0
Changing ScalesRepeated presses of the [SCALE] key will scroll through the list of available scales. Holding [SUB] when pressing [SCALE] will scroll
Operation13 – Scale Master® Pro
Rolling a MeasurementTo take a measurement with the Scale Master Pro:1) Turn the unit on. If the display does not show zero (0), press the [ON/CLEAR
Using the Memory FunctionThe Memory function allows you to add rolled or counted values. However, you cannot add dimensioned (rolled) and non-dimensio
SCALE MASTER® PRO IntroductionThe Scale Master Pro Multi-Scale Digital Plan Measure has been specifically designed to simplify takeoffs from architec
Additional Memory Functions[SET] [M+]Subtracts the value in the main display from the value stored in Memory.[RCL] [M+]Displays the total accumulated
Programming ModeThe Scale Master Pro allows you to pre-set frequently used values, including: ● Custom Scales (3 Imp/3 Met)● Height valueTo begin se
Setting Custom ScalesYou can store six Custom Scales: three in Imperial Mode and three in Metric Mode. You can set a custom scale two ways: by “rollin
(cont’d)6) Press [COUNT] (S) to increase or [RCL] (T) to decrease the selected digit. Press the [M+] (X) key to move to the next digit to the right or
4) To change the units of measurement, press [UNITS] until your desired units appear. Press the [M+] (X) or the [LxW] (W) key to begin setting the d
Setting a HeightThe height function is used to enter a height value for finding volume.To set a height:1) Press [SET] [LxW] to access the height funct
Finding Area and VolumeThe Scale Master Pro can calculate Area and Volume once you have your values set for Length, Width, and (for Volume) Height. Fi
Additional Area/Volume Functions[RCL] [LxW]Displays the value stored in the Length register. Repeated presses of the [LxW] key will toggle through a
APPENDIXError/Auto-Range FunctionError Message – If you make an incorrect entry (such as trying to add dimensioned and non-dimensioned values togeth
Battery/Automatic Shut-OffThe Scale Master Pro is powered by two 3-Volt CR-2032 Lithium batteries (6 volts total). To conserve battery power, the unit
TABLE OF CONTENTSGetting StartedKey Definitions ...1Operation Keys ...
Default SettingsThe following are the factory defaults of the Scale Master Pro: Default DefaultSettings Imperial MetricMode ARCH ARCHScale 1/4&quo
SpecificationsPower Source:Two 3-Volt CR-2032 lithium batteries.Approximately 400 hours normal use.Display Method:LCD with commas, annunciators and ze
Repair and ReturnWarranty, Repair and Return InformationReturn Guidelines:1. Please read the Warranty in this User's Guide to determine if your
WarrantyWarranty Repair Service — USACalculated Industries (“CI”) warrants this product against defects in materials and workmanship for a period of o
DisclaimerCI M A K ES NO WA R R A N T Y OR R EPR ESEN TATION, EITHER EXPRESS OR IMPLIED, WITH RESPECT TO THE PRODUCT’S QUALITY, PERFORMANCE, MERCHANTA
MailCalculated Industries, Inc.4840 Hytech DriveCarson City, NV 89706 U.S.A.Phone(775) 885–4900Fax(775) 885–[email protected] Wide
Software copyrighted and licensed to Calculated Industries by Scale Master Technologies, LLC, 2009. User’s Guide copyrighted by Calculated Industrie
AppendixError/Auto-Range Function ... 24Interference ... 24Battery/Automatic Shut
GETTING STARTEDKey DefinitionsOperation Keys[ON/CLEAR] – On/Clear Turns power on. Press once to clear the display. This will not clear the last roll
[RESET] – Hardware Reset If your Scale Master Pro should ever “lock up,” use a paperclip or similar size object to press the RESET hole. Clears all v
[LOCK] – Lock Switch The Lock Switch is located on the side of the unit. When the lock is activated, a lock symbol will be displayed in the LCD. Whi
[UNITS] – Unit Selection Repeated presses of [UNITS] will scroll through the available units of measurement. See “Imperial Units” and “Metric Units
Measuring Keys[LxW] – Length/Width/Area Enters the displayed measurement as length. Once a length is entered, enters a second measurement as width an
Comments to this Manuals