Scale Master II®is a registered trademark ofCALCULATED INDUSTRIES, INC.All other trademarks are the propertyof their respective owners.Software copyri
User’s Guide — 98.If using the Serial port, a “Driver is Active On COM1” prompt willthen appear.If using the USB port, a “Driver is Active On USB” pro
10 — Scale Master®II – PC InterfaceWindows 3.1 Installation1. Select Run from the Start menu, and click Browse. Select the win31folder and double-clic
User’s Guide — 11ABOUT THE CONFIGURATION MENUConnection — The first section of the Configuration Menu,Connection, selects the Communications Portthat
12 — Scale Master®II – PC InterfaceTERMINATING SEQUENCE — The selections on the left side ofthe Configuration Menu have to do with how your data istra
User’s Guide — 13SENDING VALUES TO YOURSPREADSHEET APPLICATION PROGRAMThe PC interface program sends a single value(the main value onyour display) mea
14 — Scale Master®II – PC Interface7. When finished rolling, press the [SET] key on your Scale Master IIto send the value on the display to the select
User’s Guide — 15Sending Areas or VolumesSending Areas1. Open your spreadsheet or application program and click on adesired cell. 2. Roll the first di
16 — Scale Master®II – PC InterfaceClearing Values in RegistersValues stored in Length, Width and Height are semi-permanentlystored, meaning they will
User’s Guide — 17Sending Counts 1. Press the [COUNT] key to count the value. 2. Press [RCL] [COUNT] to move this counted value to the maindisplay of y
18 — Scale Master®II – PC InterfaceEXITING AND REACTIVATINGTHE PROGRAMExiting SM2 CONNECT Interface Program The Disable option within the Configuratio
User’s Guide — 1TABLE OF CONTENTSINTRODUCTION...2CONNECTING THE SCALE
User’s Guide — 19PC INTERFACE COMMANDS[SET]Sends the displayed value to a cell in your PC’s spreadsheet orestimating program. The numerical value on t
20 — Scale Master®II – PC InterfaceTROUBLESHOOTINGQ: Why won’t my SMIIsend values to my computer?A: Check or adjust any of the following:1. Check the
User’s Guide — 214. Are any USB devices attached to your computer?a. Devices such as digital cameras, digitizers, USB mice, etc.may interfere.b. Remov
22 — Scale Master®II – PC InterfaceHYPERTERMINAL (For Serial Connection)1. If the Scale Master IIis not sending values to your bid program oryour spr
User’s Guide — 23The settings should read: Bits per second 9600Data bits8Parity NoneStop bits 1Flow control None7. After changing the settings click O
24 — Scale Master®II – PC InterfaceLICENSE AND LIMITED WARRANTYPLEASE READ THIS LICENSE CAREFULLY BEFORE USING THISSOFTWARE. BY USING THIS SOFTWARE, Y
User’s Guide — 25d) Notwithstanding any other terms in this License, if the Software is licensed asan upgrade or update, then you may only use the Sof
26 — Scale Master®II – PC InterfaceTHIS LIMITED WARRANTY IS THE ONLY WARRANTY PROVIDED BYCALCULATED. CALCULATED AND ITS LICENSORS EXPRESSLY DISCLAIMAL
User’s Guide — 27LEGAL NOTESSoftware copyrighted and licensed to Calculated Industries, Inc., byScale Master Technologies, LLC, 2003.User’s Guide copy
28 — Scale Master®II – PC InterfaceNOTES6215UG-E-G 9/2/03 2:38 PM Page 28
2 — Scale Master®II – PC InterfaceINTRODUCTIONThe Scale Master®II PC Interface Kit lets you transfer values fromyour Scale Master II (SMII)digital pla
User’s Guide — 3CONNECTING THE SCALE MASTER IITO YOUR PCFollow the instructions below to connect your Scale Master II (SMII)Digital Plan Measuring Sys
4 — Scale Master®II – PC InterfaceINSTALLING THE PC INTERFACESOFTWAREThe next step is installing the PC Interface software program to yourcomputer’s h
User’s Guide — 5(continued)3. If your CD Drive does not Autostart, select Run from the Start menuand click Browse. Select your CD Drive within the “Lo
6 — Scale Master®II – PC Interface4. Click the “Install SM2 PC Interface Software” button on the Startupmenu. A small menu will pop up which says, “Th
User’s Guide — 76. When installation is complete, the final menu will prompt you tofinish the setup. Check “Yes, Launch the program file”, then click“
8 — Scale Master®II – PC Interface7. The SM2 Connect Configuration Menu will be displayed.7a. If you are using the serial port connection, and no chan
Comments to this Manuals